RAIN GUARD TPC-0205 Manuel d'instructions télécharger pdf

RECOMMENDED USES:

Split face Block Stucco

Smooth Block Cement Plaster

Adobe Block Slump Block

Brick Painted surfaces

Horizontal Concrete Chalked Surfaces

Vertical Concrete Aggregate Panels

Wood Natural Stone

Wall Board EFIS

Clay Roof Tiles Painted Surfaces

COVERAGE RATES (THEORETICAL):

Substrate ___ Sq Ft/ Gallon

Dense Masonry 100-150

Porous Masonry 60-100

Stucco/EFIS 150-200

Wood 175-200

Painted Surfaces 400

Notes: *Use of fluted or scored block or raked joints will

increase surface areas by 20%-30% or more and de-

crease coverage rates.

Warranty Period: Three Year Limited

USA

International

Part Numbers: 1 Gallon TPC-0201 TPC-0201-CA

5 Gallon TPC-0205 TPC-0205-CA

Wet Look™

with Micro-Lok™Technology

“Wet–Look” Gloss Masonry and Wood Sealer

PRODUCT DESCRIPTION

WET LOOK is a high solids, water based, modified silicone

acrylic water repellent and sealer that protects and beautifies

vertical and horizontal, interior and exterior masonry, concrete

and painted surfaces with a beautiful gloss/wet look finish.

Features and Benefits:

 Gloss finish repellent and alkali resistant sealer for masonry

and concrete

 Protects and beatifies surfaces with a wet look finish

 For use on interior and exterior surfaces

 Resists flaking and has excellent adhesion

 Protection not effected by weathering or UV light

 Excellent wear and abrasion resistance

 Virtually maintenance free

 Breathable – does not trap moisture

HOW TO USE

WET LOOK is supplied ready to use. DO NOT THIN. Mix

thoroughly prior to use. Avoid application in windy weather.

In hot weather, lightly dampen surfaces with clean fresh water

to avoid premature or flash drying.

Porous Vertical Surfaces

Start first coat application at the top of the wall. Apply flood

coat with a 6”-8” rundown and back-roll material into surface

voids. Apply second coat when the first coat is dry.

Vertical Concrete Surfaces

Material may be applied as soon as the forms are removed.

Surfaces shall be clean and free of form oils and release agents.

Start first coat application at the top of the wall. Apply satura-

tion coat and back-roll materials. Apply second coat when the

first coat is dry. (Continued on back)

TECHNICAL DATA:

Solvent ` Water

Material Type Modified Silicone Acrylic

Active Solids Content Approximately 25.0%

Odor Low Odor

Appearance When Dry Dries to a Gloss Finish

V.O.C. <15 g/L

Flash Point None

Weight Approximately 8.7 lbs./gal.

Surface Dry Time Approx 1 Hr

Recoat Approx 1 Hour

Full Chemical Cure 72-96 Hours

Application Temp 45° to 90° F

1 2

Wet Look™ 1
RECAUTIONS: 2

Résumé du contenu

Page 1 - Wet Look™

RECOMMENDED USES: Split face Block Stucco Smooth Block Cement Plaster Adobe Block Slump Block Brick Painted surfaces Horizontal

Page 2 - RECAUTIONS:

PRECAUTIONS: Do not apply to surfaces if moisture content is greater than 15% as measured with an electronic moisture meter. Do not apply materials In

Commentaires sur ces manuels

Pas de commentaire

RAIN GUARD TPC-0205 Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Non RAIN GUARD TPC-0205. RAIN GUARD TPC-0205 Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non RAIN GUARD TPC-0205